Abstract:
Matlab files containing raw data collected using the program "HC2S3snowwind.CR1" running on Campbell Scientific CR1000 dataloggers. Datalogger "C" was used during all ice stations. On the 8th of October a second mast and logger ("A") were installed on what became the final day of Ice Station 4, and both loggers were deployed at stations 6 and 7, with "C" containing the longer records for each ... station as it was always installed first and (conditions permitting) left out longer.
The sensors on these masts consist of: RM Young "Wind Sentry" Vane and Anemometer set (on top of each mast), no serial numbers Rotronics HC2S3 temperature and relative humidity sensors with standard polyethylene filters Upper sensor, mast "C": s/n 60837541 Lower sensor, mast "C": s/n 60837536 Upper sensor, mast "A": s/n 60837468 Lower sensor, mast "A": s/n 60834204 RM Young "Wind Sentry" anemometers (without vane) at 3 additional elevations on each mast Wenglor YHO3NCT8 photoelectric sensors at 4 heights on each mast. The upper sensor and the third sensor from the top were oriented facing up, while the others faced down. The upper three sensors were purchased in 2012, from a batch of these sensors manufactured in a new Eastern European factory while the lowest sensor on each mast came from a lot purchased in 2007, manufactured in Wenglor's German factory and extensively tested for use in snow.
Data contained in these .mat files includes the following variables, with units:
Textdates: CSI formatted dates, UTC except for station 2, which was (accidentally) UTC+12 Datenm: Matlab "datenumber", all UTC except for station 2, which is also UTC+12 hours. Battvolt: battery voltage Wptemp: temperature of the Wiring Panel thermister, degrees C Temp 1: air temperature above approximately 50cm, ventilated HC2S3 rotronics sensor, degrees C RH1: relative humidity (WRT water) above approximately 50cm, ventilated HC2S3 rotronics sensor, % Temp 2: air temperature above approximately 200cm, ventilated HC2S3 rotronics sensor, degrees C RH2: relative humidity (WRT water) above 197cm, ventilated HC2S3 rotronics sensor, % Snow1: snow particles per 10second interval at approximately 10cm Snow2: snow particles per 10second interval at approximately 50cm Snow3: snow particles per 10second interval at approximately 100cm Snow4: snow particles per 10second interval at approximately 200cm Wind1: average speed (m/s) at approximately 250cm during 10s interval Wind1max: maximum speed at approximately 250cm during 10s interval Wind2: average speed (m/s) at approximately 100cm during 10s interval Wind2max: maximum speed at approximately 100cm during 10s interval Wind3: average speed (m/s) at approximately 120cm during 10s interval Wind3max: maximum speed at approximately 120cm during 10s interval Wind4: average speed (m/s) at approximately 50cm during 10s interval Wind4max: maximum speed at approximately 50cm during 10s interval WindDir: wind direction at approximately 250cm, degrees, relative to mast orientation (needs correction to true)
Measurement heights varied by ice station and by mast being used.
Description:
The MODIS Level-3 Land products are generated by the MODIS Adaptive Processing System (MODAPS), located at the NASA Goddard Space Flight Center, as gridded output in the Integerized Sinusoidal (ISIN) projection. These data products are then sent to the EDC DAAC for archive and distribution. The ISIN projection is unique to the MODIS land products, analogous to the Sinusoidal projection except that the ISIN projection is centered about 0° longitude and special coefficients are used to flatten the ellipsoid. The ISIN projection was devised for the Level-3+ products because it employs a tessellation scheme, efficient organization, and hierarchical management of the multi-resolution data acquired by the MODIS sensor.
Description:
The Geographic Resources Analysis Support System (GRASS) is a Geographic Information System (GIS) used for data management, image processing, graphics production, spatial modelling, and visualization of many types of data. It is free software released under GNU General Public License (GPL). Originally written by the U.S. Army Construction Engineering Research Laboratories (USA-CERL, 1982-1995), a branch of the US Army Corp of Engineers, as a tool for land management and environmental planning by the military, GRASS has evolved into a powerful utility with a wide range of applications in many different areas of scientific research. GRASS is currently used in academic and commercial settings around the world, as well as many governmental agencies including NASA, NOAA, USDA, the National Park Service, the U.S. Census Bureau, USGS, and many environmental consulting companies.
Description:
The General Cartographic Transformation Package (GCTP) is a system of software routines designed to permit the transformation of coordinate pairs from one map projection to another. The GCTP is the standard computer software used by the National Mapping Division for map projection computations.
Because of requirements internal to the EROS Data Center, the GCTP software was converted from FORTRAN to the C programming language, and several new projections were added. During the conversion process, the software was tested on the following UNIX systems: Data General running DG/UX Release 5.4R2.01 AViiON, SUN running SunOS Release 4.1.3, and Silicon Graphics running IRIX Release 5.3 IP7. In addition, the software has also been verified against the current National Mapping Division (NMD) GCTP software. This new version, GCTPC, is being made available informally on a 'user-beware' basis. EDC assumes no responsibility for the accuracy of the routines in this package.
Name:
EROS CENTER
Phone:
605-594-6151
Phone:
800-252-4547
Fax:
605-594-6589
Email:
lta at usgs.gov
Contact Address:
LTA Customer Services
U.S. Geological Survey
EROS Center
47914 252nd Street City:
Sioux Falls
Province or State:
SD
Postal Code:
57198-0001
Country:
USA
Personnel
TYLER
B.
STEVENS Role:
SERF AUTHOR
Phone:
(301) 614-6898
Fax:
301-614-5268
Email:
Tyler.B.Stevens at nasa.gov
Contact Address:
NASA Goddard Space Flight Center
Global Change Master Directory City:
Greenbelt
Province or State:
MD
Postal Code:
20771
Country:
USA
Creation and Review Dates
SERF Creation Date:
2005-05-06
SERF Last Revision Date:
2011-12-01
Links
